W A R N I N G !


W A R N I N G !

This page is full of non-facts and bullsh!t, (just like the internet and especially forums and other blogs), please do not believe entirely without exercising your intellect. Any resemblance to real things in reality is purely coincidental. You are free to interpret/misinterpret the content however you like, most likely for entertainment, but in no case is the text written on this blog the absolute truth. The blog owner and Blogger are not responsible for any misunderstanding of ASCII characters as facts. *cough* As I was saying, you are free to interpret however you like. *cough*

Thursday, March 10, 2011

Boston Acoustics HPS 10HO subwoofer repair - Day 1

Note to self: a 15.7kg white cube is very hard to carry by hand

Fuse intact.

Power on, nothing exploded. Nothing happened at all either. Fuses intact.

Took it apart.

Transformer secondary continuity check pass.

Transformer primary continuity check pass.

Ok, now this is strange.

Power cable continuity check fail. And at neutral somemore.

Knn.

Changed cable. Power on. Voltages on secondary side okay. At this moment the transformer is not connected to the power supply cum amp board.

Connected transformer to PSU board. Power on. Hum for a few seconds, fuse break.

So the good news is - transformer is okay. And the bad news is - the power supply/amp board isn't. Well, something has to be broken somewhere.

But the worse news is - there isn't any sign of damage on the power supply board.

Well, an amp board with built-in power supply is easy to get.

But the even worse news is - the stupid preamp stage board is fking hot-melt-glued to the metal plate like a motherf*cker. That means to keep things clean I'd better reuse the preamp board. But the even worse news - I can't even tell how that shit is connected to the power supply/amp board via a 7-pin connector, and what voltage it uses. And if it's working.

Well, that's enough for day 1. Diagnosis will continue after I get more fuses.

Tuesday, March 8, 2011

Random thought/quote:

The size of the audio system owner's penis is proportional to the size of the low-frequency driver.

Saturday, March 5, 2011

Almost completed - Linear post regulator

I needed a 15V power supply to replace a dead one. And something at least 2.5A.

But there are two issues:

- 15V power supplies of >2.5A are significantly more expensive than the more common 19V (at the time of my searching)
- Always expect worst-case scenario when not proven otherwise - the DC quality of these power supplies are crap. And when I say crap, it is more crap than a typical desktop computer power supply. Much more crap.

Hence the idea of using a linear regulator + filter to clean up the circuit and drop the voltage at the same time came up.

Thanks to a group of helpful and knowledgeable enthusiasts over at diyAudio forums a good design was created very quickly. I implemented one of the earlier designs but the topic has progressed even further.

I will not post the design I used out of respect for the community by keeping the internet free of bad circuits when superior ones exist, but basically the idea I used was capacitor multiplier with one RC stage at the base of the darlington, fed to a LM338 linear regulator.


I so need a camera. PC Show coming soon.

Missing input connector and output strain relief. Grommet I got was too small.

P2p build, active devices bolted to the tin case which doubles as a heatsink.

I'm getting 38°C with no load and 46°C with load for the LM338, and 34°C no load 38°C load for the transistor, taken directly from metal part of the TO-220 packaging. Same 29°C air temperature. Compare it with the 47/54 heatsink temp with the Zhaolu power supply.

I don't know if this or having the cover closed, and the surface with the components bolted-on flipped over to face the top would provide better cooling, but for certain, at these temperatures and power draw, it would not matter.

Thursday, March 3, 2011

Fun with power

Since my regulator is coming soon, I had to check how much heat will be coming out of it. So I had to see how much the amp draws and calculate from that.


0.24A. No change whether playing music or not.

Lets make it a quarter of an ampere for easy calculation. The regulator drops 4V. 4V @ 0.25A = ...1W.

That's pretty easy to dissipate with a mints tin. Heck, even 2W would be possible.

Just that the full power dissipation of 12W would be really impossible. Lets hope I'll never come to that. Can that amp draw 3A anyway?

Since the Zhaolu is now open I might as well take a few temperature readings... I've always known its power supply to be inefficient, lets take more evidence of it.

Power draw should have a somewhat linear relationship with temperature rise. In practice, the relationship between rate of heat transfer and temperature may not be linear, but the error is reduced by having the heatsink in the open with the fan blowing onto it - this minimizes the issue of different surround air temperature screwing the calculation.


Power supply power off - air temperature


Power supply on, amp off


Power supply on, amp on

18 vs 25 degree rise.

Output voltage = 15V, input voltage = 14V x √2 = 19.8V, voltage drop = ~5V, current draw = 0.25A, additional power dissipated = 1.25W, additional temperature rise = 7 degrees, thermal resistance = ~5.6ÂșC/W

Sounds logical. It is actually way lower than what it should be, but I had a fan blowing at it.

Using that thermal resistance, power used by regulator doing nothing = ~3.2W

Sounds logical.

I did remember this bugger to use 7 to 8W idling. 3.2W is for one LM317 at 20V in/15V out. There is also the negative -15V guy and a +5V guy too, so roughly would add up to around there alright, assuming power draw by the DAC + headphone amp circuit to be negligible, which it should be.

Sunday, February 27, 2011

Hmm... this does not look good


Hmm what does that number mean?

I paid a few bucks extra for this multimeter. For the thermometer function. It has an accuracy of ±5 degrees but that is enough for me - I just want a general idea of the kind of temperature the thing is running at.

And that is in degree Celsius.

Well, actually I was using the linear power supply of the Zhaolu D1.3 to power an amp.

A linear power supply of a DAC powering an amp, so, ya.

"Overclocking" anyone?

Actually, not really. I measured my Yulong T-Amp's power draw to be 4W, and that thing also uses a linear power supply.

Remember I measured the D2.5A to draw 10W.

Nonetheless, it is not good to create something without going through flame-test 3 - long term stability.


How I measured - probe inside closed chassis.

92 degrees is not good, but it's not too bad either, at least it is stable instead of increasing all the way to ∞.

It's just a bit close to the maximum operating temperature of 125°C of the LM317. But that is junction temperature - I'm measuring that of the heatsink. Include junction-to-case thermal resistance, and don't forget contact resistance, consider inaccuracy, and it is darn close to max temperature.

Fortunately LM317 has overheat shutdown. Hooray for integrated circuits.

But I don't like stuff running at near boiling point of water anyway. Maybe 80°C is the max I would go.

So, is this thing so hot because I'm "overclocking" it?

Well it's too unscientific to jump to conclusion at this point. Need to measure temperature of regulator with no load connected.

I got... 80°C.

Screw this design.

RCA couplers have arrived


The last part of the in-line attenuator has arrived.

This thing converts the female connector on the attenuator to a male to save using one extra cable, which has benefits cost and performance wise.

Why didn't I use a male connector on the attenuator in the first place and instead used two female connectors instead?, you may ask.

Well, the dimensions of the front and back are 15 x 13mm. It's actually rather compact for a DIY-ed solution. And it has to be in order to have the most compatibility. These dimensions are pretty tight for a male RCA connector. I did try to use a male connector, but the moment I on-ed the 1cm drill it cracked through the whole thing.

Even for the socket I had to look for one with a really thin body, so that the nut can fit inside the enclosure.


How the finished thing looks.


The thing in action.

So far I've tried it on two systems - the one that you see in the pic, and another one which I shall not disclose now. Lets call it system X for now.

Why am I mentioning this? Well, there are unexpected side findings. Apart from the obvious 20dB reduction in volume.

On system X, it solved a bit of balance issues (due to volume control at too low positions) as expected, at the same time the soundstage opened out/the sound became wide/sue me my audiophile language sucks.

I attributed this to the balance issue being solved - when more sound is coming from one speaker, the image feels less spacious. And/or maybe having two speakers at the same volume brings out mids and some bass better.

On the system you see in the pic, the bass became more controlled and more powerful. Could be due to the same thing as above.

*Note - none of these claims have been blind-tested.

If avoiding channel imbalance issues results in these benefits, there could be some weight in why stepped attenuators sound better than potentiometers (notice the commonalities between claimed improvements of using stepped attenuators vs my thing).

However, again, this is untested, and those who calibrate their speakers to +-0.5dB would know the truth.